! WARNING welding operations without eye protection as described above. Welder is turned on - whether the trigger is pulled or not. The welding wire is ! CAUTION live whenever the All persons operating this equipment or in the area while equipment is in use must wear protective welding gear including: welding helmet or shield with at least shade 10 lens, flame resistant clothing, leather welding gloves, and full foot protection.ThisĪll precautions described in this manual to reduce the possibility of injury to eyes and skin. Wear ear plugs when welding overhead to prevent spatter or slag from falling into ears.Įlectric arc welding operations produce intense light and heat and ultraviolet (UV) rays.Wear ANSI approved face shield or safety glasses with side shield protection when chipping or grinding metal parts.This manual to reduce the possibility of injury from flying sparks and hot metal. Never use an electric arc welder to thaw frozen pipes.įlying sparks and hot metal can cause injury.Never attempt to use this equipment at current settings or duty cycles higher than those specified on the equipment labels.When crouching, kneeling or at elevations, be sure to insulate all conductive parts, wear appropriate protective clothing, and take precautions to prevent injury from falls. Awkward welding conditions and positions can be electrically hazardous.Never allow any part of the body to touch the flux core wire and ground or grounded work piece at the same time.Always shut off electric arc welding equipment when not in use and cut off any excess wire from the wire feed gun.Verify that the work piece is securely grounded.Always shut the equipment off and unplug the power prior to moving the unit.If the welder becomes wet for any reason, be absolutely certain that it is completely clean and dry prior to attempting use! Never immerse the ! DANGER wire or wire feed Coiled welding cable should be spread out before use to avoid overheating and damage to insulation.Properly supported and grounded prior to beginning any electric arc welding operation. Do not operate the welder in humid, wet, rainy, or poorly ventilated areas. Always operate the welder in a clean, dry, well ventilated area.Always wear dry, protective clothing and welding gloves, and insulated footwear.Always repair or replace damaged components before operating the welder. Be sure that the insulation on all cables, wire feed gun, and power cords is not damaged. Verify that all components of the arc welder are clean and in good condition prior to operating the welder.This manual to reduce the possibility of electric shock. Improper use of electric arc welders can cause electric shock, injury, and death! Take all precautions described in All installation, maintenance, repair and operation of this equipment should be performed by qualified persons only in accordance with national, state, and local codes.Failure to follow safety precautions or instructions can cause equipment damage and/or serious personal injury or death. Before starting or servicing any electric arc welder, read and understand all instructions.NOTE: Note means any additional information pertaining to the product or its proper usage.Īlways keep a fire extinguisher accessible while performing arc welding operations. It also may mean a hazard that will only cause damage to property. Warning means a ! WARNING hazard that couldĬaution means a ! CAUTION hazard that mayĬause minor or moderate injury if the warning is ignored. Lift and/or removeĬause death or serious injury if the warning is ignored. Call 1-800- 746-5641 to purchase conversion kit (WT600400AJ) for WF2000.Īll welding accessories for the welder are inside the wire feed compartment. The WF1800 and WF1900 are NOT convertible to MIG gas usage. Welding operations may continue when the yellow lamp is no longer illuminated. A yellow lamp is illuminated on the front panel (on/off switch) if the duty cycle is exceeded. Internal components of this welder are protected from overheating with an automatic thermal switch. For example, at a 10% duty cycle, actual welding can occur for one minute, then the welder must cool for nine minutes. Welder duty cycle is the percentage of actual weld time that can occur in a ten minute interval. Welders are configured for DCEN, direct current electrode negative. As delivered from the factory, this welder can weld with. This welding system is designed for use with the Flux Core Arc Welding (FCAW) process. Internal components are thermostatically protected. The WF2000 is equipped with infinite wire speed control to accurately select the proper wire feed rate needed for various welding conditions. The Campbell Hausfeld WF1800, WF1900 and WF2000 are 70 amp, single phase 115 volt input, wire feed arc welding machines.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |